Autocommit from 2025-02-15 10:50:46
Klipper version: v0.12.0-432-gfec3e685c Moonraker version: v0.9.3-36-g1117890 Mainsail version: v2.13.2
This commit is contained in:
Nick
parent
c37414d558
commit
bf9be39b8f
6 changed files with 11 additions and 844 deletions
10
config_backup.cfg
Normal file
10
config_backup.cfg
Normal file
|
|
@ -0,0 +1,10 @@
|
|||
|
||||
[gcode_shell_command backup_cfg]
|
||||
command: ~/printer_data/config/autocommit.sh
|
||||
timeout: 30
|
||||
verbose: True
|
||||
|
||||
[gcode_macro BACKUP_CFG]
|
||||
description: Backs up config directory GitHub
|
||||
gcode:
|
||||
RUN_SHELL_COMMAND CMD=backup_cfg
|
||||
BIN
moonraker-sql.db
BIN
moonraker-sql.db
Binary file not shown.
|
|
@ -1,279 +0,0 @@
|
|||
[include mainsail.cfg]
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||
|
||||
[virtual_sdcard]
|
||||
path: /home/nixolas/printer_data/gcodes
|
||||
on_error_gcode: CANCEL_PRINT
|
||||
|
||||
#Klipper config for Bluer Direct Drive - Robin Nano v2, TMC2209 in UART Mode
|
||||
|
||||
|
||||
# This file contains common pin mappings for MKS Robin Nano V2
|
||||
# boards. To use this config, the firmware should be compiled for the
|
||||
# STM32F103. When running "make menuconfig", enable "extra low-level
|
||||
# configuration setup", select the 28KiB bootloader, and serial (on
|
||||
# USART3 PB11/PB10) communication.
|
||||
|
||||
# Note that the "make flash" command does not work with MKS Robin
|
||||
# boards. After running "make", run the following command:
|
||||
# ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano35.bin
|
||||
# Copy the file out/Robin_nano35.bin to an SD card and then restart the
|
||||
# printer with that SD card.
|
||||
|
||||
# ls /dev/serial/by-id/*
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
|
||||
[pause_resume]
|
||||
|
||||
[display_status]
|
||||
|
||||
|
||||
[printer]
|
||||
kinematics = cartesian
|
||||
max_velocity = 500
|
||||
max_accel = 3500
|
||||
max_z_velocity = 25 #10
|
||||
max_z_accel = 100
|
||||
|
||||
[stepper_x]
|
||||
step_pin = PE3
|
||||
dir_pin = PE2
|
||||
enable_pin = !PE4
|
||||
endstop_pin = !PA15
|
||||
|
||||
microsteps = 16 #32
|
||||
rotation_distance = 40 # rotation_distance = 400 * 32 / 160
|
||||
full_steps_per_rotation = 400
|
||||
|
||||
position_max = 300
|
||||
position_endstop = -5
|
||||
position_min = -5
|
||||
homing_speed = 50
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
step_pin = PE0
|
||||
dir_pin = !PB9
|
||||
enable_pin = !PE1
|
||||
endstop_pin = !PA12
|
||||
|
||||
microsteps = 16 # 16 #32
|
||||
rotation_distance = 40 # <full_steps_per_rotation> * <microsteps> / <steps_per_mm>
|
||||
full_steps_per_rotation = 400 # 0.9 degrees per step
|
||||
|
||||
position_endstop = -15
|
||||
position_min = -15
|
||||
position_max = 280
|
||||
homing_speed = 50
|
||||
|
||||
|
||||
|
||||
[stepper_z]
|
||||
step_pin = PB5
|
||||
dir_pin = !PB4
|
||||
enable_pin = !PB8
|
||||
|
||||
microsteps = 16 #16
|
||||
rotation_distance = 8
|
||||
full_steps_per_rotation = 200
|
||||
|
||||
position_max = 400
|
||||
position_min = -4
|
||||
endstop_pin = probe:z_virtual_endstop
|
||||
|
||||
|
||||
[stepper_z1]
|
||||
step_pin = PD15
|
||||
dir_pin = !PA1
|
||||
enable_pin = !PA3
|
||||
microsteps = 16 #16
|
||||
rotation_distance = 8
|
||||
full_steps_per_rotation = 200
|
||||
|
||||
|
||||
[extruder]
|
||||
step_pin = PD6
|
||||
dir_pin = !PD3
|
||||
enable_pin = !PB3
|
||||
microsteps = 16
|
||||
rotation_distance = 7.93
|
||||
nozzle_diameter = 0.600
|
||||
filament_diameter = 1.750
|
||||
heater_pin = PC3
|
||||
sensor_type = EPCOS 100K B57560G104F
|
||||
sensor_pin = PC1
|
||||
control = pid
|
||||
pid_kp = 31.087
|
||||
pid_ki = 1.712
|
||||
pid_kd = 141.059
|
||||
min_temp = 0
|
||||
max_temp = 255
|
||||
max_extrude_only_distance = 240
|
||||
#pressure_advance = 0.0953
|
||||
|
||||
|
||||
[heater_bed]
|
||||
heater_pin = PA0
|
||||
sensor_type = EPCOS 100K B57560G104F
|
||||
sensor_pin = PC0
|
||||
control = pid
|
||||
pid_Kp = 58.992
|
||||
pid_Ki = 0.917
|
||||
pid_Kd = 949.030
|
||||
min_temp = 0
|
||||
max_temp = 120
|
||||
|
||||
[verify_heater extruder]
|
||||
max_error = 150
|
||||
|
||||
|
||||
## FANS
|
||||
[fan] # part colling fans
|
||||
pin = PB1
|
||||
|
||||
[heater_fan HeatSink]
|
||||
pin: PB0
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
fan_speed: 1.0
|
||||
|
||||
|
||||
[bltouch]
|
||||
sensor_pin = ^PA11
|
||||
control_pin = PA8
|
||||
x_offset = 40.50
|
||||
y_offset = 8.70
|
||||
z_offset = 2.425
|
||||
pin_move_time = 0.4
|
||||
speed = 10 #5
|
||||
stow_on_each_sample = FALSE
|
||||
#position_min: -3 enable this for z-offset callibration
|
||||
|
||||
[bed_mesh]
|
||||
speed = 120 #120
|
||||
horizontal_move_z = 7 #8
|
||||
mesh_min = 42,42
|
||||
mesh_max = 290,270
|
||||
probe_count = 4,4 #6,6
|
||||
# mesh_pps: 5,3
|
||||
algorithm = bicubic
|
||||
# bicubic_tension: 0.2
|
||||
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position = 160, 140
|
||||
speed = 50
|
||||
z_hop = 8
|
||||
z_hop_speed = 5
|
||||
|
||||
|
||||
[screws_tilt_adjust]
|
||||
screw1: 1.30,24.20
|
||||
screw1_name: Front Left
|
||||
screw2: 166.30,24.20
|
||||
screw2_name: Front Right
|
||||
screw3: 166.30,194.20
|
||||
screw3_name: Rear Right
|
||||
screw4: 1.30,194.20
|
||||
screw4_name: Rear Left
|
||||
horizontal_move_z: 10.
|
||||
speed: 80
|
||||
screw_thread: CW-M4
|
||||
|
||||
|
||||
|
||||
[temperature_sensor pi]
|
||||
sensor_type: temperature_host
|
||||
min_temp: 10
|
||||
max_temp: 100
|
||||
|
||||
[temperature_sensor mcu]
|
||||
sensor_type: temperature_mcu
|
||||
min_temp: 0
|
||||
max_temp: 100
|
||||
|
||||
|
||||
[gcode_macro CALIBRATE_BED]
|
||||
gcode:
|
||||
G28 X0 Y0
|
||||
G28 Z0
|
||||
G90
|
||||
bed_mesh_calibrate profile=bluey method=automatic
|
||||
|
||||
|
||||
[gcode_macro FILAMENT_LOAD]
|
||||
gcode:
|
||||
M83
|
||||
G92 E0.0
|
||||
G1 E480 F350
|
||||
G92 E0.0
|
||||
M82
|
||||
|
||||
[gcode_macro FILAMENT_UNLOAD]
|
||||
gcode:
|
||||
M83
|
||||
G92 E0.0
|
||||
G1 E-480 F350
|
||||
G92 E0.0
|
||||
M82
|
||||
|
||||
|
||||
[z_tilt]
|
||||
z_positions:
|
||||
0,117.5
|
||||
180,117.5
|
||||
points:
|
||||
5,117.5
|
||||
180,117.5
|
||||
horizontal_move_z: 10
|
||||
retries: 10
|
||||
retry_tolerance: 0.02
|
||||
|
||||
|
||||
[respond]
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.025000, 0.042500, 0.025000, -0.052500
|
||||
#*# -0.025000, 0.007500, -0.017500, -0.095000
|
||||
#*# -0.020000, 0.015000, -0.020000, -0.097500
|
||||
#*# 0.060000, 0.082500, 0.055000, -0.015000
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 42.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 4
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 42.0
|
||||
#*# x_count = 4
|
||||
#*# max_y = 219.99
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 219.99
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*#
|
||||
#*# [bed_mesh bluey]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.320000, 0.235000, 0.192500, 0.237500
|
||||
#*# 0.082500, 0.040000, -0.010000, 0.085000
|
||||
#*# 0.100000, 0.020000, -0.005000, 0.035000
|
||||
#*# 0.355000, 0.195000, 0.115000, 0.100000
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 42.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 4
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 42.0
|
||||
#*# x_count = 4
|
||||
#*# max_y = 270.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 289.98
|
||||
|
||||
|
|
@ -1,279 +0,0 @@
|
|||
[include mainsail.cfg]
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||
|
||||
[virtual_sdcard]
|
||||
path: /home/nixolas/printer_data/gcodes
|
||||
on_error_gcode: CANCEL_PRINT
|
||||
|
||||
#Klipper config for Bluer Direct Drive - Robin Nano v2, TMC2209 in UART Mode
|
||||
|
||||
|
||||
# This file contains common pin mappings for MKS Robin Nano V2
|
||||
# boards. To use this config, the firmware should be compiled for the
|
||||
# STM32F103. When running "make menuconfig", enable "extra low-level
|
||||
# configuration setup", select the 28KiB bootloader, and serial (on
|
||||
# USART3 PB11/PB10) communication.
|
||||
|
||||
# Note that the "make flash" command does not work with MKS Robin
|
||||
# boards. After running "make", run the following command:
|
||||
# ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano35.bin
|
||||
# Copy the file out/Robin_nano35.bin to an SD card and then restart the
|
||||
# printer with that SD card.
|
||||
|
||||
# ls /dev/serial/by-id/*
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
|
||||
[pause_resume]
|
||||
|
||||
[display_status]
|
||||
|
||||
|
||||
[printer]
|
||||
kinematics = cartesian
|
||||
max_velocity = 500
|
||||
max_accel = 3500
|
||||
max_z_velocity = 25 #10
|
||||
max_z_accel = 100
|
||||
|
||||
[stepper_x]
|
||||
step_pin = PE3
|
||||
dir_pin = PE2
|
||||
enable_pin = !PE4
|
||||
endstop_pin = !PA15
|
||||
|
||||
microsteps = 16 #32
|
||||
rotation_distance = 40 # rotation_distance = 400 * 32 / 160
|
||||
full_steps_per_rotation = 400
|
||||
|
||||
position_max = 300
|
||||
position_endstop = -5
|
||||
position_min = -5
|
||||
homing_speed = 50
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
step_pin = PE0
|
||||
dir_pin = !PB9
|
||||
enable_pin = !PE1
|
||||
endstop_pin = !PA12
|
||||
|
||||
microsteps = 16 # 16 #32
|
||||
rotation_distance = 40 # <full_steps_per_rotation> * <microsteps> / <steps_per_mm>
|
||||
full_steps_per_rotation = 400 # 0.9 degrees per step
|
||||
|
||||
position_endstop = -15
|
||||
position_min = -15
|
||||
position_max = 280
|
||||
homing_speed = 50
|
||||
|
||||
|
||||
|
||||
[stepper_z]
|
||||
step_pin = PB5
|
||||
dir_pin = !PB4
|
||||
enable_pin = !PB8
|
||||
|
||||
microsteps = 16 #16
|
||||
rotation_distance = 8
|
||||
full_steps_per_rotation = 200
|
||||
|
||||
position_max = 400
|
||||
position_min = -4
|
||||
endstop_pin = probe:z_virtual_endstop
|
||||
|
||||
|
||||
[stepper_z1]
|
||||
step_pin = PD15
|
||||
dir_pin = !PA1
|
||||
enable_pin = !PA3
|
||||
microsteps = 16 #16
|
||||
rotation_distance = 8
|
||||
full_steps_per_rotation = 200
|
||||
|
||||
|
||||
[extruder]
|
||||
step_pin = PD6
|
||||
dir_pin = !PD3
|
||||
enable_pin = !PB3
|
||||
microsteps = 16
|
||||
rotation_distance = 7.93
|
||||
nozzle_diameter = 0.600
|
||||
filament_diameter = 1.750
|
||||
heater_pin = PC3
|
||||
sensor_type = EPCOS 100K B57560G104F
|
||||
sensor_pin = PC1
|
||||
control = pid
|
||||
pid_kp = 31.087
|
||||
pid_ki = 1.712
|
||||
pid_kd = 141.059
|
||||
min_temp = 0
|
||||
max_temp = 255
|
||||
max_extrude_only_distance = 240
|
||||
#pressure_advance = 0.0953
|
||||
|
||||
|
||||
[heater_bed]
|
||||
heater_pin = PA0
|
||||
sensor_type = EPCOS 100K B57560G104F
|
||||
sensor_pin = PC0
|
||||
control = pid
|
||||
pid_Kp = 58.992
|
||||
pid_Ki = 0.917
|
||||
pid_Kd = 949.030
|
||||
min_temp = 0
|
||||
max_temp = 120
|
||||
|
||||
[verify_heater extruder]
|
||||
max_error = 150
|
||||
|
||||
|
||||
## FANS
|
||||
[fan] # part colling fans
|
||||
pin = PB1
|
||||
|
||||
[heater_fan HeatSink]
|
||||
pin: PB0
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
fan_speed: 1.0
|
||||
|
||||
|
||||
[bltouch]
|
||||
sensor_pin = ^PA11
|
||||
control_pin = PA8
|
||||
x_offset = 19.1
|
||||
y_offset = 31.1
|
||||
#z_offset = 2.425
|
||||
pin_move_time = 0.4
|
||||
speed = 10 #5
|
||||
stow_on_each_sample = FALSE
|
||||
#position_min: -3 enable this for z-offset callibration
|
||||
|
||||
[bed_mesh]
|
||||
speed = 120 #120
|
||||
horizontal_move_z = 7 #8
|
||||
mesh_min = 42,42
|
||||
mesh_max = 290,270
|
||||
probe_count = 4,4 #6,6
|
||||
# mesh_pps: 5,3
|
||||
algorithm = bicubic
|
||||
# bicubic_tension: 0.2
|
||||
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position = 160, 140
|
||||
speed = 50
|
||||
z_hop = 8
|
||||
z_hop_speed = 5
|
||||
|
||||
|
||||
[screws_tilt_adjust]
|
||||
screw1: 1.30,24.20
|
||||
screw1_name: Front Left
|
||||
screw2: 166.30,24.20
|
||||
screw2_name: Front Right
|
||||
screw3: 166.30,194.20
|
||||
screw3_name: Rear Right
|
||||
screw4: 1.30,194.20
|
||||
screw4_name: Rear Left
|
||||
horizontal_move_z: 10.
|
||||
speed: 80
|
||||
screw_thread: CW-M4
|
||||
|
||||
|
||||
|
||||
[temperature_sensor pi]
|
||||
sensor_type: temperature_host
|
||||
min_temp: 10
|
||||
max_temp: 100
|
||||
|
||||
[temperature_sensor mcu]
|
||||
sensor_type: temperature_mcu
|
||||
min_temp: 0
|
||||
max_temp: 100
|
||||
|
||||
|
||||
[gcode_macro CALIBRATE_BED]
|
||||
gcode:
|
||||
G28 X0 Y0
|
||||
G28 Z0
|
||||
G90
|
||||
bed_mesh_calibrate profile=bluey method=automatic
|
||||
|
||||
|
||||
[gcode_macro FILAMENT_LOAD]
|
||||
gcode:
|
||||
M83
|
||||
G92 E0.0
|
||||
G1 E480 F350
|
||||
G92 E0.0
|
||||
M82
|
||||
|
||||
[gcode_macro FILAMENT_UNLOAD]
|
||||
gcode:
|
||||
M83
|
||||
G92 E0.0
|
||||
G1 E-480 F350
|
||||
G92 E0.0
|
||||
M82
|
||||
|
||||
|
||||
[z_tilt]
|
||||
z_positions:
|
||||
0,117.5
|
||||
180,117.5
|
||||
points:
|
||||
5,117.5
|
||||
180,117.5
|
||||
horizontal_move_z: 10
|
||||
retries: 10
|
||||
retry_tolerance: 0.02
|
||||
|
||||
|
||||
[respond]
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.025000, 0.042500, 0.025000, -0.052500
|
||||
#*# -0.025000, 0.007500, -0.017500, -0.095000
|
||||
#*# -0.020000, 0.015000, -0.020000, -0.097500
|
||||
#*# 0.060000, 0.082500, 0.055000, -0.015000
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 42.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 4
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 42.0
|
||||
#*# x_count = 4
|
||||
#*# max_y = 219.99
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 219.99
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.280
|
||||
#*#
|
||||
#*# [bed_mesh bluey]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.320000, 0.235000, 0.192500, 0.237500
|
||||
#*# 0.082500, 0.040000, -0.010000, 0.085000
|
||||
#*# 0.100000, 0.020000, -0.005000, 0.035000
|
||||
#*# 0.355000, 0.195000, 0.115000, 0.100000
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 42.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 4
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 42.0
|
||||
#*# x_count = 4
|
||||
#*# max_y = 270.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 289.98
|
||||
|
|
@ -1,286 +0,0 @@
|
|||
[include mainsail.cfg]
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||
|
||||
[virtual_sdcard]
|
||||
path: /home/nixolas/printer_data/gcodes
|
||||
on_error_gcode: CANCEL_PRINT
|
||||
|
||||
#Klipper config for Bluer Direct Drive - Robin Nano v2, TMC2209 in UART Mode
|
||||
|
||||
# [include adxlmcu.cfg]
|
||||
|
||||
# This file contains common pin mappings for MKS Robin Nano V2
|
||||
# boards. To use this config, the firmware should be compiled for the
|
||||
# STM32F103. When running "make menuconfig", enable "extra low-level
|
||||
# configuration setup", select the 28KiB bootloader, and serial (on
|
||||
# USART3 PB11/PB10) communication.
|
||||
|
||||
# Note that the "make flash" command does not work with MKS Robin
|
||||
# boards. After running "make", run the following command:
|
||||
# ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano35.bin
|
||||
# Copy the file out/Robin_nano35.bin to an SD card and then restart the
|
||||
# printer with that SD card.
|
||||
|
||||
# ls /dev/serial/by-id/*
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
|
||||
[pause_resume]
|
||||
|
||||
[display_status]
|
||||
|
||||
|
||||
[printer]
|
||||
kinematics = cartesian
|
||||
max_velocity = 500
|
||||
max_accel = 2500
|
||||
max_z_velocity = 25 #10
|
||||
max_z_accel = 100
|
||||
|
||||
[stepper_x]
|
||||
step_pin = PE3
|
||||
dir_pin = PE2
|
||||
enable_pin = !PE4
|
||||
endstop_pin = !PA15
|
||||
|
||||
microsteps = 16 #32
|
||||
rotation_distance = 40 # rotation_distance = 400 * 32 / 160
|
||||
full_steps_per_rotation = 400
|
||||
|
||||
position_max = 300
|
||||
position_endstop = -5
|
||||
position_min = -5
|
||||
homing_speed = 50
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
step_pin = PE0
|
||||
dir_pin = !PB9
|
||||
enable_pin = !PE1
|
||||
endstop_pin = !PA12
|
||||
|
||||
microsteps = 16 # 16 #32
|
||||
rotation_distance = 40 # <full_steps_per_rotation> * <microsteps> / <steps_per_mm>
|
||||
full_steps_per_rotation = 400 # 0.9 degrees per step
|
||||
|
||||
position_endstop = -15
|
||||
position_min = -15
|
||||
position_max = 280
|
||||
homing_speed = 50
|
||||
|
||||
|
||||
|
||||
[stepper_z]
|
||||
step_pin = PB5
|
||||
dir_pin = !PB4
|
||||
enable_pin = !PB8
|
||||
|
||||
microsteps = 16 #16
|
||||
rotation_distance = 8
|
||||
full_steps_per_rotation = 200
|
||||
|
||||
position_max = 400
|
||||
position_min = -4
|
||||
endstop_pin = probe:z_virtual_endstop
|
||||
|
||||
|
||||
[stepper_z1]
|
||||
step_pin = PD15
|
||||
dir_pin = !PA1
|
||||
enable_pin = !PA3
|
||||
microsteps = 16 #16
|
||||
rotation_distance = 8
|
||||
full_steps_per_rotation = 200
|
||||
|
||||
|
||||
[extruder]
|
||||
step_pin = PD6
|
||||
dir_pin = !PD3
|
||||
enable_pin = !PB3
|
||||
microsteps = 16
|
||||
rotation_distance = 7.93
|
||||
nozzle_diameter = 0.600
|
||||
filament_diameter = 1.750
|
||||
heater_pin = PC3
|
||||
sensor_type = EPCOS 100K B57560G104F
|
||||
sensor_pin = PC1
|
||||
control = pid
|
||||
pid_kp = 31.087
|
||||
pid_ki = 1.712
|
||||
pid_kd = 141.059
|
||||
min_temp = 0
|
||||
max_temp = 255
|
||||
max_extrude_only_distance = 240
|
||||
#pressure_advance = 0.0953
|
||||
|
||||
|
||||
[heater_bed]
|
||||
heater_pin = PA0
|
||||
sensor_type = EPCOS 100K B57560G104F
|
||||
sensor_pin = PC0
|
||||
control = pid
|
||||
pid_Kp = 58.992
|
||||
pid_Ki = 0.917
|
||||
pid_Kd = 949.030
|
||||
min_temp = 0
|
||||
max_temp = 120
|
||||
|
||||
[verify_heater extruder]
|
||||
max_error = 150
|
||||
|
||||
|
||||
## FANS
|
||||
[fan] # part colling fans
|
||||
pin = PB1
|
||||
|
||||
[heater_fan HeatSink]
|
||||
pin: PB0
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
fan_speed: 1.0
|
||||
|
||||
|
||||
[bltouch]
|
||||
sensor_pin = ^PA11
|
||||
control_pin = PA8
|
||||
x_offset = 19.1
|
||||
y_offset = 31.1
|
||||
#z_offset = 2.425
|
||||
pin_move_time = 0.4
|
||||
speed = 10 #5
|
||||
stow_on_each_sample = FALSE
|
||||
#position_min: -3 enable this for z-offset callibration
|
||||
|
||||
[bed_mesh]
|
||||
speed = 120 #120
|
||||
horizontal_move_z = 7 #8
|
||||
mesh_min = 42,42
|
||||
mesh_max = 290,270
|
||||
probe_count = 6,6
|
||||
# mesh_pps: 5,3
|
||||
algorithm = bicubic
|
||||
# bicubic_tension: 0.2
|
||||
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position = 160, 140
|
||||
speed = 50
|
||||
z_hop = 8
|
||||
z_hop_speed = 5
|
||||
|
||||
[input_shaper]
|
||||
shaper_freq_y: 29.1
|
||||
shaper_type_y: mzv
|
||||
shaper_freq_x: 71.4
|
||||
shaper_type_x: mzv
|
||||
|
||||
|
||||
[screws_tilt_adjust]
|
||||
screw1: 1.30,24.20
|
||||
screw1_name: Front Left
|
||||
screw2: 166.30,24.20
|
||||
screw2_name: Front Right
|
||||
screw3: 166.30,194.20
|
||||
screw3_name: Rear Right
|
||||
screw4: 1.30,194.20
|
||||
screw4_name: Rear Left
|
||||
horizontal_move_z: 10.
|
||||
speed: 80
|
||||
screw_thread: CW-M4
|
||||
|
||||
|
||||
|
||||
[temperature_sensor pi]
|
||||
sensor_type: temperature_host
|
||||
min_temp: 10
|
||||
max_temp: 100
|
||||
|
||||
[temperature_sensor mcu]
|
||||
sensor_type: temperature_mcu
|
||||
min_temp: 0
|
||||
max_temp: 100
|
||||
|
||||
|
||||
[gcode_macro CALIBRATE_BED]
|
||||
gcode:
|
||||
G28 X0 Y0
|
||||
G28 Z0
|
||||
G90
|
||||
bed_mesh_calibrate profile=bluey method=automatic
|
||||
|
||||
|
||||
[gcode_macro FILAMENT_LOAD]
|
||||
gcode:
|
||||
M83
|
||||
G92 E0.0
|
||||
G1 E480 F350
|
||||
G92 E0.0
|
||||
M82
|
||||
|
||||
[gcode_macro FILAMENT_UNLOAD]
|
||||
gcode:
|
||||
M83
|
||||
G92 E0.0
|
||||
G1 E-480 F350
|
||||
G92 E0.0
|
||||
M82
|
||||
|
||||
|
||||
[z_tilt]
|
||||
z_positions:
|
||||
0,117.5
|
||||
180,117.5
|
||||
points:
|
||||
5,117.5
|
||||
180,117.5
|
||||
horizontal_move_z: 10
|
||||
retries: 10
|
||||
retry_tolerance: 0.02
|
||||
|
||||
|
||||
[respond]
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.025000, 0.042500, 0.025000, -0.052500
|
||||
#*# -0.025000, 0.007500, -0.017500, -0.095000
|
||||
#*# -0.020000, 0.015000, -0.020000, -0.097500
|
||||
#*# 0.060000, 0.082500, 0.055000, -0.015000
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 42.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 4
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 42.0
|
||||
#*# x_count = 4
|
||||
#*# max_y = 219.99
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 219.99
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.910
|
||||
#*#
|
||||
#*# [bed_mesh bluey]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.320000, 0.235000, 0.192500, 0.237500
|
||||
#*# 0.082500, 0.040000, -0.010000, 0.085000
|
||||
#*# 0.100000, 0.020000, -0.005000, 0.035000
|
||||
#*# 0.355000, 0.195000, 0.115000, 0.100000
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 42.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 4
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 42.0
|
||||
#*# x_count = 4
|
||||
#*# max_y = 270.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 289.98
|
||||
|
|
@ -9,6 +9,7 @@ on_error_gcode: CANCEL_PRINT
|
|||
#Klipper config for Bluer Direct Drive - Robin Nano v2, TMC2209 in UART Mode
|
||||
|
||||
# [include adxlmcu.cfg]
|
||||
[include config_backup.cfg]
|
||||
|
||||
# This file contains common pin mappings for MKS Robin Nano V2
|
||||
# boards. To use this config, the firmware should be compiled for the
|
||||
|
|
|
|||
Loading…
Add table
Reference in a new issue